Best Storage Configurations for Refurbished Servers

Storage Solutions

The right storage configuration makes a bigger difference to how a server feels than almost any other choice. The same refurbished server can be slow or fast, fragile or resilient, depending on the drives, RAID level and controller settings you choose. This guide explains the options and gives recommended setups for common workloads.

Quick answer: for most small business servers, use SSDs in RAID 1 or RAID 10 for the operating system, virtual machines and databases, and large SAS or SATA hard drives in RAID 6 (or RAID 10) for bulk file storage and backups. Use a hardware RAID controller with a battery or flash-backed cache, and keep a spare drive on hand.

Choose the drive type

Drive typeStrengthsBest for
SATA SSDFast, affordable, low powerBoot, VMs and general workloads
SAS SSDFast, dual-port, built for serversBusy databases and VM hosts
NVMe SSDFastest, on supported servers and backplanesDatabases, caching, heavy I/O
SAS hard drive (10K/15K)Durable, faster than SATA HDDLegacy applications, mixed workloads
Nearline SAS or SATA hard drive (7.2K)Large capacity, low cost per TBFile shares, archives, backup targets
Good to know: servers come in small form factor (2.5 inch) or large form factor (3.5 inch) drive bay versions. 2.5 inch bays fit more SSDs and fast drives; 3.5 inch bays fit the largest capacity hard drives. Check which your server has before ordering drives. See our server hard drives and server SSDs.
server storage solutions

Choose the RAID level

RAID levelMinimum drivesSurvivesUse it for
RAID 121 drive failureBoot drives and small servers
RAID 531 drive failureRead-heavy data on smaller SSD arrays
RAID 642 drive failuresLarge hard drive arrays and file storage
RAID 1041 drive per mirrorVMs and databases needing speed and safety

Our guide to RAID configurations explains each level in more detail.

Watch out: avoid RAID 5 on large hard drives. Rebuilding a big array after a failure takes a long time and stresses the remaining drives, and a second failure during the rebuild loses the array. RAID 6 or RAID 10 is safer for large disks.

Recommended configurations

WorkloadSuggested setup
File and print server2 SSDs in RAID 1 for the OS, plus 4 or more large hard drives in RAID 6 for shares
Virtualisation host4 or more SSDs in RAID 10 for VMs, or separate RAID 1 for the hypervisor
Database serverSSDs in RAID 10, logs and data on separate volumes if the database supports it
Backup targetLarge hard drives in RAID 6, with a second copy off site
ZFS or TrueNAS storageController set to HBA mode so the software manages the disks directly
Pro tip: Dell 14th generation servers can use a BOSS card, a small mirrored M.2 boot device, so the operating system does not take up front drive bays. HPE Gen10 servers offer M.2 boot options too. Freeing bays leaves more room for data drives.

Controller settings that matter

  • Write cache: enable write-back cache only when the controller has a working battery or flash-backed cache, to avoid data loss on power failure.
  • Hot spare: assign a spare drive so a rebuild starts automatically when a drive fails.
  • Patrol read and consistency checks: leave them enabled to find bad sectors early.
  • Firmware: keep controller and drive firmware current.

Frequently asked questions

What is the best RAID for a small business server?

RAID 1 for two-drive servers, RAID 10 for performance with four or more drives, and RAID 6 for large file storage on hard drives.

Should I use SSDs or hard drives in a server?

Use SSDs for the OS, virtual machines and databases, and hard drives where you need a lot of capacity at low cost, such as file shares and backups.

Can I mix SSDs and hard drives in one server?

Yes, as separate RAID arrays. Do not mix drive types within the same array.

What is HBA mode?

HBA mode passes drives straight to the operating system without hardware RAID. It is used with software-defined storage such as ZFS.

Need more capacity? Browse our storage servers, or configure a server with the drives and RAID you need.

Server Site